manual:chapter1:installation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:chapter1:installation [2021/07/28 08:07]
claudio [What is needed]
manual:chapter1:installation [2021/07/28 08:37] (current)
claudio [newRPL ROM installation Instructions (for Prime G1 model only)]
Line 30: Line 30:
  
 |{{:manual:warning-145066_640.png?100 |Warning!}} Installing **newRPL** will overwrite the entire 2 MiB of flash in the calculator. This includes the ROM, and also all user flash banks in Port 2. Using **newRPL** for the first time will also erase all RAM, including __TEMPOB__, __USEROB__, __PORT 0__ and __ERAM 1__. Remember to backup everything, including your libraries in Port 2 before installing the **newRPL** ROM.| |{{:manual:warning-145066_640.png?100 |Warning!}} Installing **newRPL** will overwrite the entire 2 MiB of flash in the calculator. This includes the ROM, and also all user flash banks in Port 2. Using **newRPL** for the first time will also erase all RAM, including __TEMPOB__, __USEROB__, __PORT 0__ and __ERAM 1__. Remember to backup everything, including your libraries in Port 2 before installing the **newRPL** ROM.|
 +
 +====newRPL ROM installation Instructions (for Prime G1 model only) ====
 +
 +  - **First time install only**: Connect the cable and start **the Connectivity Kit that came with the calculator**. Make sure it downloads the latest Prime firmware version. Do not need to flash it to the calculator yet.
 +  - Run the **Prime Firmware Bundler** application distributed with newRPL Desktop. Follow the 3-step process: The first step needs the directory where the Connectivity Kit stores the firmware. This should auto-populate unless you have some custom installation, in most cases no action is needed. The second step needs the location of the firmware file **newrplG1.bin** downloaded from the links above or from Sourceforge. On step 3 simply press proceed and watch for any errors. If it shows success, then newRPL was bundled into the firmware correctly.
 +  - Start the Connectivity Kit again, this time update the calculator firmware as usual.
 +  - After it's complete, the calculator will start normally. To switch to newRPL, press **On+Symb** to reset the calculator, then quickly **Esc<sup>hold</sup>**. Don't release Esc until you see a message from newRPL saying that "Install will wipe out RAM"
 +  - Once **newRPL** is installed for the first time, all future updates can be made using **newRPL Desktop**. Doing it this way will update **newRPL** without affecting the Prime firmware at all.
 +  - **Important**: If you wish to update the Prime firmware to a newer version, don't forget to run the **Prime Firmware Bundler** after the Connectivity Kit downloads and extracts the file, and before you flash it to the calculator. Flashing a stock firmware without **newRPL** bundled in will completely remove **newRPL** from the calculator.
  
 ====How to revert to the stock ROM==== ====How to revert to the stock ROM====
  
-To revert back to the stock HP ROM that came with the HP50g, just follow the directions above for loading the **newRPL** ROM, the only difference being the ROM file used.  In this case, use the stock HP50g ROM file.  For this case, the contents of the **update.scp** file would need to be changed to reflect this new ROM filename.+To revert back to the stock HP ROM that came with the calculator, just follow the directions above for loading the **newRPL** ROM, the only difference being the ROM file used.  In this case, use the stock ROM file from the manufacturer.  When using an SD card (50g model only), the contents of the **update.scp** file would need to be changed to reflect this new ROM filename.
  
-The ROM update will take about 2 minutes during which time a series of hexadecimal values will scroll down the screen.  At the end of the update the total size of the ROM will be printed, press **ENTER**.  If all goes well you will be presented with the stock HP50g screen.+The ROM update will take about 2 minutes during which time a series of hexadecimal values will scroll down the screen.  At the end of the update the total size of the ROM will be printed, press **ENTER**.  If all goes well you will be presented with the standard calculator screen.
  
 The latest HP50g stock ROM file (if you don't already have it) is currently available on the **hpcalc.org** website at [[http://www.hpcalc.org/details/7097|this link]]. The latest HP50g stock ROM file (if you don't already have it) is currently available on the **hpcalc.org** website at [[http://www.hpcalc.org/details/7097|this link]].
  
 The downloadable ZIP archive contains another zip file, **2MB FIX.zip**, which contains a ROM image that can fix problems with Port 2.  Because **newRPL** overwrites all of Port 2, **this ROM file, //2MB_215f.bin//, is required** in order to revert back after the **newRPL** ROM was installed. The downloadable ZIP archive contains another zip file, **2MB FIX.zip**, which contains a ROM image that can fix problems with Port 2.  Because **newRPL** overwrites all of Port 2, **this ROM file, //2MB_215f.bin//, is required** in order to revert back after the **newRPL** ROM was installed.
 +
 +For other models, always try to find a ROM image file that is padded all the way to the end of the flash memory. This will guarantee **newRPL** is completely removed from your calculator and Port2 will be fully functional.
 +
 +On the **Prime G1** model, reverting back to stock ROM does not require removing **newRPL**. Press **On<sup>hold</sup>+A<sup>hold</sup>+F** then press any of the shifts **Shift<sup>hold</sup>+Help** to reset the calculator. Very quickly press **Esc<sup>hold</sup>** and don't let go until you see HP logo and you are back to Prime world.
 +
 +To completely uninstall **newRPL** from a **Prime G1** model, simply go to the Connectivity Kit folder where the firmware is and delete all files in there (these files contain **newRPL** bundled in). This will force the Connectivity Kit to re-download the latest version of the stock firmware. Then flash the stock firmware as usual and **newRPL** will be gone completely.
  
  • manual/chapter1/installation.1627484848.txt.gz
  • Last modified: 2021/07/28 08:07
  • by claudio